Click for Burger Click for Westport Click for Nordhavn Click for Glendinning Click for YF Listing Service

Glendinning auto pilot acting up

Discussion in 'Luhrs Yacht' started by Joe McKairnes, May 24, 2021.

You need to be registered and signed in to view this content.
  1. Joe McKairnes

    Joe McKairnes Member

    Joined:
    Sep 13, 2020
    Messages:
    94
    Location:
    lacey twp NJ
    ran 3 hours on AP and everything was fine until about 2 minutes from home port - Port engine revved up, then went to almost idle - Starboard engine stayed fine (master). tried a few times - same issue...

    Any thoughts as to what is causing this?
  2. MBevins

    MBevins Senior Member

    Joined:
    May 23, 2008
    Messages:
    1,162
    Location:
    Windsor On. Canada
    It's actually your engine synchronizer. They're basically mechanical so first things first, check all the linkage points on the unit. Then the engine linkage.
    If that's all good check back for further instructions.
  3. Joe McKairnes

    Joe McKairnes Member

    Joined:
    Sep 13, 2020
    Messages:
    94
    Location:
    lacey twp NJ
    I checked the 90 degree joint at the engine, greased them. Then disconnected each tach cable... they turn freely.... anything else I should check?
  4. MBevins

    MBevins Senior Member

    Joined:
    May 23, 2008
    Messages:
    1,162
    Location:
    Windsor On. Canada
    Did you inspect the actual unit?
    Baring any linkage issues at the unit, your best to call Glendenning's service department. They are extremely helpful and might be able to point you at a particular item.
  5. YachtForums

    YachtForums Administrator

    Joined:
    Dec 22, 2002
    Messages:
    20,353
    Location:
    South Florida
    Glendinning notified. :)
  6. MBevins

    MBevins Senior Member

    Joined:
    May 23, 2008
    Messages:
    1,162
    Location:
    Windsor On. Canada
    Thanks Carl.
  7. Joe McKairnes

    Joe McKairnes Member

    Joined:
    Sep 13, 2020
    Messages:
    94
    Location:
    lacey twp NJ
    Thank you all! I did send a note in... awaiting response..I really do like the unit.. hoping to figure it out as I have some long offshore runs coming up!
  8. Joe McKairnes

    Joe McKairnes Member

    Joined:
    Sep 13, 2020
    Messages:
    94
    Location:
    lacey twp NJ
    This forum is the greatest!!
  9. Robertoman

    Robertoman Member

    Joined:
    Dec 15, 2010
    Messages:
    71
    Location:
    San Diego
    What was it?
  10. Joe McKairnes

    Joe McKairnes Member

    Joined:
    Sep 13, 2020
    Messages:
    94
    Location:
    lacey twp NJ
    Still troubleshooting...
  11. CGlendinning

    CGlendinning New Member

    Joined:
    Nov 4, 2019
    Messages:
    1
    Location:
    Myrtle Beach, SC
    Hi Joe- I just spoke to Rick our Synchronizer guru here at Glendinning and he told me he is currently troubleshooitng your unit. Hopefully he can help you find a solution shortly!
  12. Joe McKairnes

    Joe McKairnes Member

    Joined:
    Sep 13, 2020
    Messages:
    94
    Location:
    lacey twp NJ
    You guys are great..appreciate the help... great company... great product!
  13. Joe McKairnes

    Joe McKairnes Member

    Joined:
    Sep 13, 2020
    Messages:
    94
    Location:
    lacey twp NJ
    turns out the failure was at the 90 degree adapter at the front of the Yanmar engine. Got a new one coming.... man I miss this great feature!