Marlow 65' seatrial vibration

Here's an excerpt from another model that shows the tinkering and logic you often see with Marlow.

She has an additional 200+ gallons in fuel capacity and draws 4" less water due to the innovative design of engines placement and reduced shaft angle which have increased speed by 5% and fuel economy by approximately 10%, increasing her already industry leading performance and range.
​

Now understand that's all theoretical, the kind of thing designers hope for but long before proven. That is changing engine placement to impact draft and changing shaft angles to try to impact fuel economy or add a little speed. Squeezing in a little more fuel.

Now I have no idea what changes were made in the 65's or why particular arrangements, but Marlow never has seemed able or willing to get a model that worked well and stick to it for a while. Sometimes they'd change models, sometimes not. A few years ago you had the 57, 61, and 65 and now the 58, 62, and 66 and how new and improved. More likely you had the 65A, 65B, 65C, 66 progression.

By comparison we had a Sunseeker Manhattan 65. That wasn't a new boat, but just another version of the 63. 63 was galley down and 65 was galley up. Same hull that had been used for years. We were able to run several before buying. Then finally they decided to redesign and came out with a 66 but that was after riding a design a long time and thinking very carefully about changes they'd make.

I'm very hesitant over new models of even dependable brands. I like proven models, but with Marlow they're always new models or slightly changed.

I'd also pay attention to how quickly boats seem to hit the used market. Sure there are those who have a life change or something happen that forces them to sell quickly. However, if a builder introduces a new 80' model and within 2 years half of those built are already on the market, there's a reason. Marlow's biggest single fiasco was the 97E and all three built were quickly on the used market. Two did so rather quietly as they didn't want to lower the value of their own boat. The other one sued.

There are many other examples. Nordhavn built a 120', during rough times and really over their heads with what they promised. The one and only one quickly was on the used market.

We have a 44' Riva. The original model had issues but by the time it was relabeled the Rivarama Super, the issues were all resolved and has been wonderful.

Westport has been criticized by some as being dated at different times. However, we found a lot of comfort in being able to charter multiple boats of a model and have something like the ultimate test drives.

Doing things the Marlow way is just going to lead to issues and some solutions that work out better in the designers head than in reality.

There were two Marlow's hauled both having the running gear removed. The tech told me they were replacing the vibration dampers aft of the couplings that failed and let the shaft slip back. Yikes

Where are the generators? The early 2000's Marlow I ran had them mounted outboard of the engines. Of course it had stand up engine room height, but the engine room length from bow to stern was short and there was minimal crew cabin. Marlow put all that space up into the cabins where he 'beat the competition'. Of course years later there was a decision on that boat to replace the generators. I asked the next captain how they did it with them being outboard of the engines. He said they stripped them to the block and got them out of the boat with lots of effort. The new ones were installed by stripping them to the block and reassembling them in the engine room. Cost a fortune and the new generator warranty was crumpled up and tossed in a garbage can.

On this 2002 model, they appear to be mounted aft of the engines, at least as shown here on the starboard side. The listing specifies twin 20kW NL, so I'm assuming that the other one is on the port side; no pictures show it, though.


I'm planning to step on board this boat next week and should have a better idea of the overall layout then.

Aft of the engine makes a lot of sense. Looks like good access around it. Why no hush box?

It's a good question. One possible answer is this part of the listing: '3" Lead / Foam Engine Room Insulation' -- perhaps the thinking is that by insulating the whole engine room, it's less important to hush the generators?

Here's the best picture from the listing which would show that: