Click for Mulder Click for Abeking Click for Nordhavn Click for Burger Click for Furuno

zincs on hydraulic lifts causing leaks?

Discussion in 'Technical Discussion' started by Bamboo, Nov 28, 2017.

You need to be registered and signed in to view this content.
  1. Bamboo

    Bamboo Senior Member

    Joined:
    Dec 19, 2008
    Messages:
    934
    Location:
    Palm Beach, FL
    Has anyone had a worn/used up zinc found to the cause of a hydraulic leak on an aft lifting platform?
  2. Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,432
    Location:
    Fort Lauderdale
    Yes, it can. If there is electrolysis it can eat up the shaft on the rams and cause the seals to get eaten up......it's a very remote situation though and if the lift is done properly by the manufacturer usually the ram shaft and seals sit out of the water.....
  3. Bamboo

    Bamboo Senior Member

    Joined:
    Dec 19, 2008
    Messages:
    934
    Location:
    Palm Beach, FL
    Have you seen this happen on new vessels?
  4. Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    12,649
    Location:
    Satsuma, FL
    SeaRays; Yes
    Same lift company makes the same assembly's for other boat mfg's also.
  5. Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,432
    Location:
    Fort Lauderdale
    Yes, on a 1 year old Prestige that had electrolysis issues.
  6. T.K.

    T.K. Senior Member

    Joined:
    Jan 31, 2007
    Messages:
    1,013
    Location:
    Cairo - Egypt
    I have seen the same problem on Volvo Penta DPH stern drives. The steering rams and the trim rams were leaking hydraulic oil from around the shaft due due to galvanic corrosion of the ram body especially the area around the shaft seal. This occured on a vessel which was only months old. The hydraulic rams were replaced, more stainless steel grounding wires fitted to the DPH drives and realated components including fitting a galvanic isolator on the shore power lead and the problem never reoccured. The boat is now 5 years old.
  7. Bamboo

    Bamboo Senior Member

    Joined:
    Dec 19, 2008
    Messages:
    934
    Location:
    Palm Beach, FL
    No leaks since I stopped leaving the platform above the water but lower than all the way up. The zincs were at about 65%-70% so zincs/corrosion was not the issue. I believe leaving it less than all the way up was the issue as that is the only factor which changed and the leaks ceased.
  8. Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    12,649
    Location:
    Satsuma, FL
    I must have took a wrong turn somewhere. Maybe Albuquerque..:)

    Can you expand on this a lil more please? What relation to water level would the zincs, seals, other hardware have change to stop the leaks?
    Or maybe, less pressure on the rams making the leak from all the way up?
    Less weight out of the water?
    Could you expand on the design or mfg? Drawings or pictures could help.

    A few systems I have had anything to do with has a latch to capture the platform, lock it up and relive pressure from the cylinders. Maybe this is a part issue.
    Last edited: Dec 7, 2017
  9. Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,432
    Location:
    Fort Lauderdale
    The shaft is corroded where the seal sits on it in the all of the way (natural) up position. Saltwater probably sits in the seal where it meets the ram. Doesn't the lift have safety locks that engage when it's in the all of the way up position? Some do and some do not.