Click for Westport Click for Mulder Click for Comfort Click for MotorCheck Click for Glendinning

Ugly paint mural in need of removal on fiberglass**

Discussion in 'Technical Discussion' started by Beauregard, Nov 23, 2014.

You need to be registered and signed in to view this content.
  1. Beauregard

    Beauregard New Member

    Joined:
    Oct 12, 2014
    Messages:
    21
    Location:
    Massachusetts
    I got this ugly painting on the aft portion of my vessel. (please see attached) I am looking to restore the fiberglass to the original gelcoat. I understand by just painting it white may look like garbage in the end.

    What would you do in order to get ride of this mural? I'd rather do this the less costly approach.

    Thanks!

    Attached Files:

  2. AMG

    AMG YF Moderator

    Joined:
    Jul 26, 2004
    Messages:
    5,375
    Location:
    Sweden
    If you are lucky it will go away with just rubbing..?
  3. Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    12,649
    Location:
    Satsuma, FL
    Is that on a fiberglass bulkhead or on a real sliding glass (safety) door or panel?
    If it's fiberglass; I'd try plastic razor blades, oven cleaner, painters hand cleaner.
    I had some bad luck with fiberglass paint remover, it did damage the gel finish. If you go there, pratice on small spots several times and I'd still keep the work area small.
    Good luck.
  4. SeaEric

    SeaEric YF Historian

    Joined:
    Jan 28, 2007
    Messages:
    1,360
    Location:
    out on the dock
    +1 on the oven cleaner. Use the old original full strength Easy-Off heavy duty stuff. Forget the "fume free" low dose version as it won't work.
  5. CaptTom

    CaptTom Senior Member

    Joined:
    Jan 26, 2006
    Messages:
    1,949
    Location:
    Palm Beach to Ft Lauderdale
    That's a Silverton so the wall is probably a formica veneer over plywood. You can remove the formica and replace it. If you do, thoroughly check the wood for moisture and replace while open. Those walls and the side triangles especially tend to wick up water that rots the non-marine grade wood.
  6. Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    12,649
    Location:
    Satsuma, FL
    Formica??
    Plastic razor blade and a rum, maybe two....
    I learned a long time ago, not much really sticks to formica, mostly just sits there.
    Pressure washer should probably blow it away but capture the run off some how.
  7. Beauregard

    Beauregard New Member

    Joined:
    Oct 12, 2014
    Messages:
    21
    Location:
    Massachusetts
    Thanks everyone! I will try a small portion with the high non fume oven cleaner. I will be sure to let you know.
  8. Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    12,649
    Location:
    Satsuma, FL
    If there is a West Marine store or paint supply shop close, You would be amazed what those plastic razor blades can do. If it's really formica, you're done in minutes without a chemical slurry.
  9. Beauregard

    Beauregard New Member

    Joined:
    Oct 12, 2014
    Messages:
    21
    Location:
    Massachusetts
    Excellent, I will pick a few up this weekend and show the progress..
  10. Beauregard

    Beauregard New Member

    Joined:
    Oct 12, 2014
    Messages:
    21
    Location:
    Massachusetts
    Ok- I just tried the Oven cleaner and it did work. I also used the plastic razor blade and that also worked good. I am thinking that the material is defiantly formica. This is going to need a base coat to cover mural remains.. image1.JPG
  11. RER

    RER Senior Member

    Joined:
    Jan 20, 2009
    Messages:
    1,532
    Location:
    Newport Beach CA
    1. Sand.
    2. Paint.
    3. Admire Newly Painted Bulkhead.
  12. Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    12,649
    Location:
    Satsuma, FL
    If it is really formica, the fiberglas paint remover (gel / paste) will work,,, IF it's really formica...
    If you're not 100% positive yet, keep up with what you're doing. Looks like some hardware in the bulkhead that may be an effort to finish around it. If a smooth surface can be found under the paint, may save some finishing time to keep striping.
  13. Beauregard

    Beauregard New Member

    Joined:
    Oct 12, 2014
    Messages:
    21
    Location:
    Massachusetts
    What is puzzeling is that the top portion seems like the original color comes back, without an issue. The bottom portion, blue...... Not so much....
  14. Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,432
    Location:
    Fort Lauderdale
    I would just prime and paint it with Awlgrip or something else.