Click for JetForums Click for YF Listing Service Click for Cross Click for Abeking Click for Walker

Priming Cummins QSM-11s

Discussion in 'Engines' started by Capt Bill11, Oct 12, 2014.

You need to be registered and signed in to view this content.
  1. Capt Bill11

    Capt Bill11 Senior Member

    Joined:
    Feb 27, 2006
    Messages:
    1,458
    Location:
    Sarasota/Ft. Lauderdale FL
    Any tips or tricks to priming the fuel system on a QSM-11?
  2. Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    12,649
    Location:
    Satsuma, FL
    Pre-charging the filters usually is a big plus. Young healthy kid with big hands to work the plungers would be the next plan.
  3. Capt Bill11

    Capt Bill11 Senior Member

    Joined:
    Feb 27, 2006
    Messages:
    1,458
    Location:
    Sarasota/Ft. Lauderdale FL
    It's my understanding you do not prime the filters on the engine. Just turn the key on for 15 seconds or so, let the pump run tell it stops and repeat a couple of times.
  4. Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    12,649
    Location:
    Satsuma, FL
    I think I'm reading key on for 15 seconds and an electric pump will primp and purge the system. I don't think so. It may not have a priming plunger on the fuel pump, but I'm pretty sure it's still mechanical.
    OR, are you thinking turning the motor over for 15 second attempts. Correct. That is why it's important to precharge the filters.
    You may want to consider a electric lift or priming pump to help save time and eliminate a possible mess.
    Kafue likes this.
  5. Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,432
    Location:
    Fort Lauderdale
    I do a service on qsm11's sometimes. I always pre-fill the secondaries and also make sure the racors are full as well. The secondaries sit perfectly verticle on the back of the engine on a bracket and can be filled to full and screwed right on. If memory serves me right they also have a shutoff valve right near the filter that can be shut as well, although it's been a while so that might be for the coolant filter. Doing that I have never had to do anything, but turn the key on and start them up.
  6. Capt Bill11

    Capt Bill11 Senior Member

    Joined:
    Feb 27, 2006
    Messages:
    1,458
    Location:
    Sarasota/Ft. Lauderdale FL
    OK, filled the Racor, did not prime the engine mount filter that was mounted high on the front of the engine as I was told that was not needed. Tried the turn the key on for 15 sec. to run the pump. No pump sound. Put the throttle control in neutral lock position and cranked it over with the throttle advanced. Engine fired up after 30 seconds or less of cranking. Let it run at high idle for 15 plus minutes then took it up to max RPM for several seconds. All good now. Thanks.
    Kafue likes this.
  7. Capt Ralph

    Capt Ralph Senior Member

    Joined:
    Sep 8, 2004
    Messages:
    12,649
    Location:
    Satsuma, FL
    Sounds good.
    Question; you were told precharging the filter was not needed by a Cummins shop or heavy? Any explanation for that reasoning?
    SOP is precharge but if there is something to it, I'm open to learn something new also.
    It worked for you and that is good.
    30 seconds of cranking continuous may have been avoided with a precharged filter. Starters need luv and a easy life when possible. Spares are not on every corner.
  8. Kafue

    Kafue Senior Member

    Joined:
    Nov 29, 2006
    Messages:
    1,164
    Location:
    Gold Coast Australia
    An electric prime pump is always a good addition to any engine.
  9. Chasm

    Chasm Senior Member

    Joined:
    Mar 30, 2013
    Messages:
    137
    Location:
    Germany
    The reason not to pre fill the final fuel filters of some engines is that there may be junk in the fuel that blocks or damages the pump and/or the injectors. Say common rail engines with 2 micron final filters.
  10. K1W1

    K1W1 Senior Member

    Joined:
    Sep 30, 2005
    Messages:
    7,388
    Location:
    My Office
    I have primed plenty of fuel and oil filters albeit with clean product and never caused any damage to the rest if the system.

    If you fill one with dirty fuel then you deserve what happens.
  11. Capt J

    Capt J Senior Member

    Joined:
    Jul 11, 2005
    Messages:
    14,432
    Location:
    Fort Lauderdale
    I too have done the same and agree. I am not going to put a secondary on that is dry, even the pre-common rail MAN filters that mounted at an angle I still pre-filled 2/3 of the way before putting on, opening the bleed screws and hand pumping it.
  12. Chasm

    Chasm Senior Member

    Joined:
    Mar 30, 2013
    Messages:
    137
    Location:
    Germany
    And there we have the difference between the reason why something gets written into a service manual and what you can get away with if you know what you are doing. :D (And more importantly knowing what you can't do.)
  13. jhall767

    jhall767 Senior Member

    Joined:
    Jan 14, 2010
    Messages:
    319
    Location:
    Middle River MD
    As long as you are pre-filtering the fuel down to two microns before filling the filter you should be ok. If not why would you put "clean" unfiltered fuel through your injectors? The engines have a filter priming sequence - follow it.