Click for Delta Click for Abeking Click for Cross Click for Mag Bay Click for Ocean Alexander

80's POST Bow Railing Pulpit Piece Needed

Discussion in 'Post Yacht' started by mwwhit1, Dec 3, 2013.

You need to be registered and signed in to view this content.
  1. mwwhit1, Dec 3, 2013
    #1
    mwwhit1

    mwwhit1 Senior Member

    Joined:
    Jan 19, 2006
    Messages:
    239
    Location:
    Jersey City NJ\Boca Raton FL
    Does anyone know of a stainless bow railing removed and sitting somewhere? Since I bought the boat the railing at the tip of the pulpit has been bent. I'm looking for this front piece that joins into the rest of the railing and the 4 vertical stanchions on the pulpit. I'm pretty sure the pulpit\rail is the same on the 42 - 46 models for this front section.

    Figure this is easier than trying to have it straightened or replaced if one is laying around.

    Thanks, Mark.
  2. RER, Dec 3, 2013
    #2
    RER

    RER Senior Member

    Joined:
    Jan 20, 2009
    Messages:
    1,542
    Location:
    Newport Beach CA
    It probably isn't. The damage as you describe would be much simpler to have repaired vs buying and replacing the entire bow rail.
  3. mwwhit1, Dec 4, 2013
    #3
    mwwhit1

    mwwhit1 Senior Member

    Joined:
    Jan 19, 2006
    Messages:
    239
    Location:
    Jersey City NJ\Boca Raton FL
    Not looking to replace\ship the whole rail. It is three pieces with the pulpit part bolted to each side. Only want the rail going around the pulpit which is around 4'x5' in size.
  4. RER, Dec 4, 2013
    #4
    RER

    RER Senior Member

    Joined:
    Jan 20, 2009
    Messages:
    1,542
    Location:
    Newport Beach CA
    Well, if anyone has a Post bow rail laying around and they're willing to sell you part of it you'll be good to go.
  5. Beau, Dec 4, 2013
    #5
    Beau

    Beau Senior Member

    Joined:
    Jan 15, 2010
    Messages:
    2,261
    Location:
    Beaufort, NC
    Mmwhit

    Is your rail original, I thought they were all one piece rails?
  6. mwwhit1, Dec 4, 2013
    #6
    mwwhit1

    mwwhit1 Senior Member

    Joined:
    Jan 19, 2006
    Messages:
    239
    Location:
    Jersey City NJ\Boca Raton FL
    It certainly looks to be original. My guess is if the boat came with a pulpit (maybe an option?) then the rail around the pulpit was spliced\bolted into the sides. I'll have to take a pic when I am back at the boat. It has a smaller piece of tubing inside the joint that has bolts through each side to hold it together.
  7. Beau, Dec 4, 2013
    #7
    Beau

    Beau Senior Member

    Joined:
    Jan 15, 2010
    Messages:
    2,261
    Location:
    Beaufort, NC
    Maybe someone like RT46 can confirm that his is pieced also?
  8. P46-Curaçao, Dec 4, 2013
    #8
    P46-Curaçao

    P46-Curaçao Senior Member

    Joined:
    Mar 8, 2013
    Messages:
    734
    Location:
    Curaçao (CW), Hollywood (FL) and Amsterdam (NL)
    Old picture, but gives you an idea

    s2013-06-29 09.44.jpg
  9. Beau, Dec 4, 2013
    #9
    Beau

    Beau Senior Member

    Joined:
    Jan 15, 2010
    Messages:
    2,261
    Location:
    Beaufort, NC
    Thanks P46. Decide on a watermaker yet?
  10. P46-Curaçao, Dec 4, 2013
    #10
    P46-Curaçao

    P46-Curaçao Senior Member

    Joined:
    Mar 8, 2013
    Messages:
    734
    Location:
    Curaçao (CW), Hollywood (FL) and Amsterdam (NL)
    Hi BEAU, I think about the Katadyn 40 or 80 model, but a friend of mine knows a boat owner that has a (almost) new one in his garage...so wait to see what he's got and then decide, I would like to make one myself, but have so much boat work to do...it would be wiser to buy one!
  11. mwwhit1, Dec 4, 2013
    #11
    mwwhit1

    mwwhit1 Senior Member

    Joined:
    Jan 19, 2006
    Messages:
    239
    Location:
    Jersey City NJ\Boca Raton FL
    Perfect Pic. Thanks!
  12. P46-Curaçao, Dec 4, 2013
    #12
    P46-Curaçao

    P46-Curaçao Senior Member

    Joined:
    Mar 8, 2013
    Messages:
    734
    Location:
    Curaçao (CW), Hollywood (FL) and Amsterdam (NL)
    Even a better (old) picture, it shows it's a separate piece

    s2013-03-27 13.22.jpg
  13. ruby, Dec 5, 2013
    #13
    ruby

    ruby Member

    Joined:
    Apr 22, 2012
    Messages:
    230
    Location:
    Long Island
    I have the same bow rail on my 1986 46 Post, I am sure that any canvas guy who bends stainless steel can remake the top part of your pulpit bow rail. The lower vertical stanchions are die-pressed and would be difficult to create.
  14. RT46, Dec 5, 2013
    #14
    RT46

    RT46 Senior Member

    Joined:
    Feb 22, 2011
    Messages:
    1,058
    Location:
    Long Island, NY
    I have the same bow rail on my 46 Post